Anchor-seal, Inc.
anchor-seal  
Anchor-Seal, Inc.

Anchor-Seal Tin Series RTV-2 Silicone Rubber
Condensation cure, no cure inhibition, cast epoxy, polyester, and polyurethane, molds for prototype parts, electronic potting, glove molds.

Product
Base
(Activator)		 Shore A
Hardness
(+ / -4)
1 day
Shore A
Hardness
(+ / -4)
3 day 		Tear
Resistance (ppi)
ASTM D624
Die B		 Tensile Strength
(psi)
ASTM D412		 Elongation
(%)
ASTM D412		 Mixed
Viscosity
(CPS)
GI-184 w/ GI-1000A
Off White
(Blue)		 22 26 90 +/- 10 380 +/- 25 450 +/- 25 50,000 - 60,000
MSDS Sheets: GI-184 Base, GI-1000 Activator Art Foundry - Thixotropic (non-flowing) - use GI Thixotropic Activator vs 1000A for Brushable Applications.
Anchorseal
GI-300
Beige
(Blue)		 45 50 25 +/- 5 600 +/- 45 160 +/- 15 7,000 - 15,000
MSDS Sheet: GI-300 Base, GI-300 Activator Casting of Low-Metal Parts, Electrical Potting and Encapsulation
Anchorseal
GI-1000 *
White
(Blue)		 28 32 100 +/- 15 525 +/- 25 300 +/- 25 50,000 - 65,000
MSDS Sheets: GI-1000 Base, GI-1000 Activator Industry Leader for 10 Years in all Phases of Mold Making, Ease of Use, Reliable Results
Anchorseal
GI-1110 *
White
(Blue)		 5 10 75 +/- 15 275 +/- 25 450 +/- 25 7,000 - 15,000
MSDS Sheets: GI-1110 Base, GI-1110 Activator Glove or Vacuum Molding of Intricate, Highly Detailed Parts. Extremely Easy to Demold
Anchorseal

GI-1040
Off White
(Blue)

 30 40 100 +/- 15 525 +/- 25 225 +/- 25 50,000 - 65,000
MSDS Sheets: GI-1040 Base, GI-1040 Activator PU Foam and Non-Rising Urethanes, Polyesters and Epoxies, Used Where A Free Standing Mold Can Maintain A Straight Edge
Anchorseal
XT-491B w/1000A
Off White
(Blue)		 24 26 120 +/- 10 525 +/- 25 300 +/- 25 50,000 - 70,000
MSDS Sheets: XT-491 Base, GI-1000 Activator Prototyping and Casting of Polyurethane Parts
Anchorseal

Specialty Type Products

GI-179A - Teal Use with GI-1000B, 1110B or 1040B to lower modulus / increase elongation by 100%, reduces shore hardness by 3 to 4 points
Anchorseal
GI-UFC

Ultra fast catalyst - used in place of or in combo w/ std activator to cure a mold in as little as 30 minutes
Anchorseal
MR-15 Mold release for GI Series and Platinum series, prevents bonding of Silicone to itself
Anchorseal
GI Primer Promotes adhesion of GI series to wood, fabric, plastic, metal or glass. Catalyzed silicone rubber applied in the liquid phase will chemically react with the primer surface, resulting in adhesion.
Anchorseal
GI Thinner Lowers viscosity and can softens the cured RTV. Water clear, non-reactive silicone fluid for use with GI or Platinum Series
Anchorseal

Additional Silicone's Inc products available upon request.

All activators are available in clear.
Standard Tin and Platinum Series mix ratio is 10:1 by weight, excluding P-17 Black, P-17 Black is 1:1.
All Tin Series products have a minimum of 6 month shelf life.
Tin Series products cure in 16-24 hours @ 75F.

Mixing ratio is 10 parts of Base to 1 part of Activator by weight, excluding P-17; P-17 as shown is a 1:1 ratio. Deviations from
the specified mix ratio will cause changes in the physical properties. Choose a container with a volume that is three to four times
greater than that of the rubber. Weigh the components carefully and mix thoroughly while simultaneously scraping the sides
and bottom of the container to insure that there is no unmixed portion. Place the container in a vacuum chamber and
deaerate at 28 to 29 inches of mercury vacuum until the mass of rubber rises and then collapses. Remove the mixed rubber
and carefully pour over mold, MR-15 is recommended for GI and Platinum molds.

* Translucent Base Available